Vertical Wave Guide d'installation Page 61
- Page / 238
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Connecting the T1 module (without serial interface) 3-21
Chapter 3: Setting Up the Wave IP 500 Server
Wave Server Installation Guide
Connecting the T1 module (without serial interface)
Note: This section describes how to connect the 1-port T1/PRI module without serial interface.
For information about installing the 1-port T1 module with serial interface, see page 3-20.
The T1 module supports one T1 or ISDN PRI digital trunk.
There are 2 connectors on the T1 module:
• The RJ-48C port is used to connect to the T1 or ISDN PRI network interface.
• The bantam jack located to the right of the RJ-48C port accepts a 3-conductor Bantam
cable. It is provided for diagnostic purposes and is to be used only by an authorized
technician.
The T1 module is a partial-width module that can be installed in any module slot. This module
has one alarm indicator for the T1 port. See “Alarm indicators” in Chapter 15 in the Wave
Hardware Reference Guide for more information.
To connect the T1 module:
1. Locate the RJ-48C port on the module.
2. Connect the T1 cable to the RJ-48C port.
Release 2.0 Service Pack 1
April 2011
- Wave Server 1
- Installation Guide 1
- Revision History 3
- Release 2.0 Service Pack 1 10
- April 2011 10
- Contents 11
- About This Guide 23
- Using the Help system 24
- Terms used 25
- Type conventions 25
- Related reading 26
- Support services 27
- Corporate Web site 27
- System security 27
- Compliance statements 28
- Wave Server models 29
- Underwriter’s Laboratory 31
- Industry Canada 31
- Compliance statements 1-10 32
- Chapter 1: About This Guide 32
- Before You Begin 33
- Site preparation 35
- Physical specifications 36
- Environmental requirements 36
- Required tools 37
- Safety requirements 38
- Proper lifting 39
- About the Wave IP 500 Server 42
- About the Wave IP 500 43
- Power supply 45
- Wave IP 500 expansion options 46
- Expansion modules 47
- Media Resource Module (MRM) 47
- Mounting the Wave Server 48
- Grounding the Wave Server 49
- Power failover support 52
- Installing expansion modules 53
- To install modules: 54
- About connecting modules 55
- Connecting an RJ-21X cable 56
- About connecting modules 3-17 57
- To connect the T1 module: 61
- Connecting a paging system 64
- Connecting a DSS Console 65
- To connect a DSS Console: 66
- About the Wave IP 2500 Server 68
- Minimum configuration 70
- Redundancy 70
- Fault monitoring 70
- Expansion cards and modules 71
- Expansion Units (EXUs) 72
- Wall mounting the Wave Server 74
- Mounting the Wave Server 4-9 75
- Mounting the Wave Server 4-10 76
- Mounting the Wave Server 4-11 77
- To install an EXU: 83
- To install an MRM: 85
- To install modules and cards: 86
- About cable connections 88
- Administrator PC requirements 100
- Connecting to the Wave ISM 102
- CHAPTER CONTENTS 109
- Finish, and then 113
- Initial Configuration 115
- To apply one or more HotFixes 116
- Applying HotFixes 7-3 117
- Adding or upgrading an MRM 119
- drop-down list 121
- Join Domain to 123
- Leave Domain.) 123
- Power-cycling the Wave Server 124
- Company Name 128
- OK to continue 129
- Apply to save your changes 130
- Primary Time Server 132
- Synchronize Period 132
- Password Administration 134
- To synchronize the domains: 138
- Chassis View, located in the 140
- About Wave licenses 143
- Full vs. trial licenses 144
- Obtaining Wave licenses 144
- Wave license requirements 145
- Entering Wave licenses 147
- Entering Wave licenses 8-6 148
- Entering Wave licenses 8-7 149
- Activating Wave licenses 150
- The activation process 151
- Activating Wave licenses 8-10 152
- Activating Wave licenses 8-11 153
- Activating Wave licenses 8-12 154
- Activating Wave licenses 8-13 155
- Activating Wave licenses 8-14 156
- Activating Wave licenses 8-15 157
- Software Licenses 160
- View Activity 160
- OK to close the Activity Log 161
- Applications 163
- Requirements 164
- ViewPoint requirements 165
- Requirements 9-4 166
- Entering station IDs 167
- Configuring ViewPoint 171
- To configure Act! 172
- Synchronizing system clocks 173
- Archive folder requirements 177
- Installation steps 178
- Installation steps 10-5 179
- Installation steps 10-6 180
- Installation steps 10-7 181
- Overview 183
- APPENDIX CONTENTS 185
- RJ-48X interface pinouts 189
- DB-60 interface pinouts 190
- About System Status LEDs 200
- System LED indicators 201
- /ISC2 boot 202
- Error condition indicators 204
- 1 = Custom installation 207
- Name Value Description 208
- Tools > System Settings 214
- Custom List 215
- Before you begin 218
- Troubleshooting 221
- Appendix G: Troubleshooting 222
Produits connexes et manuels pour Téléphones Vertical Wave
Téléphones Vertical Wave Guide d'installation
(292 pages)
(292 pages)
Téléphones Vertical DXP Manuel d'utilisateur
(89 pages)
(89 pages)
Téléphones Vertical FX Series Spécifications
(76 pages)
(76 pages)
Téléphones Vertical Wave Guide de l'utilisateur
(382 pages)
(382 pages)
© 2020, manymanuals.fr. Tous droits réservés | 0.632 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels